easy-on permanent anti-graffiti coating: 420ml
Non-stick easy-on makes removing graffiti effortless. Simply apply one coat to any surface for up to 20 years protection.
An Elephant never forgets and these Elephants never fade thanks to easy-on.
- Overview
- Benefits
- Application Guide
- Data Sheets
- Brochure
- Price List
- Videos
- NBS+
easy-on permanent anti-graffiti coating
easy-on is the "true permanent" anti graffiti coating for any surface.
Simply brush, roll or spray apply a single clear coat of easy-on over anything you want to protect and the unique easy-on finish will dry to form a tough non-stick barrier capable of resisting all known graffiti media for up to 20 years.
easy-on works in much the same way as a non-stick frying pan – although graffiti and contaminants can initially get purchase on the non-stick easy-on surface they are quickly and easily removed using nothing more than mild and safe cleaning agents. In many cases water is all you will need to produce a perfect result.
The easy-on coatings close knit chemical bonds facilitate shadow free removal without the surface underneath being damaged and its quartz crystal hardness ensures you wont need to reapply this anti graffiti coating once removal has taken place.
easy-on has been tested extensively for your peace of mind and is the only anti graffiti coating in the world to be awarded "True Permanent" status by the National Materials Research Institute.
If you need to protect a surface permanently from graffiti attack, then this is the product for you.
Click "Buy Now" and protect yourself from graffiti attack.
easy-on: Features & benefits
|
easy-on coating protects...
|
Application Guide
Coating performance is proportional to the degree of surface preparation. Surface must be clean, dry (<6% moisture), undamaged and free of all contaminants prior to coating.
Prepare damaged areas to original surface preparation specifications, feathering edges of any intact coating system.
For optimum application, temperature of the material should be between 10ºC and 20ºC prior to mix and application.
Gradually add total contents of Cure tin into Resin tin and stir thoroughly to a uniform consistency.
Apply by brush, small roller or spray*, without thinning.
Use a cross-lapping method of application ensuring corners and edges are covered and avoid misses. If the surface is highly porous do not attempt to cover with one application. Apply a thin coat, leave for 3 - 4 hours to partially reduce porosity, and then apply a second light and even coat.
Many modern surfaces, especially when new, have a layer of grease, oil or other contaminants on them. To ensure good adhesion it is important these surfaces are thoroughly cleaned with a water based degreaser and that the degreaser used is then washed away before attempting to apply the coating. Both the contaminants and the degreaser can reduce adhesion so cleanliness must be considered critical.
Stainless Steel: Abrade, sweep blast or high pressure water blast.
Aluminium: Degrease followed by abrading blast or chemical conversion treatment.
Galvanizing: Degrease followed by abrading or chemical conversion treatment.
Concrete: New concrete - Acid etch or abrade to remove laitence. Aged concrete must be thoroughly cleaned.
Aged Coatings: All surfaces must be clean & dry, tightly bonded and free of loose flakes and corrosion products.
Brick/stone: All surfaces must be clean and dry and free of loose material.
Timber etc: Ensure surfaces are clean and dry.
SPRAY INSTRUCTIONS:
HVLP+ Walter pilot:
- Use 2,2 bar pressure with the 1,8 mm nozzle.
- WFT should be between 25 and 40 microns.
Conventional air spray (pressure pot):
- Use 0,2 bar material pressure and 3,5 bar assisted air pressure.
- Apply the recommended WFT of around 25/30 microns.
ALWAYS CLEAN OUT THE UNIT THOROUGHLY WHEN FINISHED SPRAYING. LEAVE SMALL AMOUNT OF CLEANER IN THE SPRAY POT.
Video DemonstrationSeeing is believing so we have prepared an easy-on coating demonstration for your viewing pleasure. The video lasts around 4 minutes and contains no cheating or camera trickery. |
NBS+
easy-on protective coating is listed on the NBS Building specification system.
NBS building is a library of pre-written specification clauses with extensive guidance, suitable for a wide variety of construction projects.
Simply click the link below then scroll to down to find "easy-on protective coating".
The easy-on clause is authored in NBS format and is intended for inclusion in project specifications. From here the clause can be copied and pasted into your project specification document.
